This 1 inch wide ceramic tape is used to wrap your heater block and reduce heat transfer to both the extruder and your work piece. Fix by wrapping in kapton tape.
The tape on your Reprap will need replacing from time to time, especially when a print fails and the melted plastic gets caught up in the print head - it can sometimes stick to the ceramic tape and rip it on removal - careful not to pull on the temperature sensor wire! More
This amazing build tape is a special plastic (self adhesive) surface that is stronger and better than old tapes(such as Kapton and Blue Tape), and holds objects on the bed so well. It also lasts significantly longer. More
Replicator 2 and 2X Interface (LCD/Button) Assembly (used and tested)
This assembly is from a trade in machine and is used and tested. It includes the screen, buttons, SD Carrier Board, and the metal case. Just undo 2 screws from the base of the assembly (that screw down into the base of the machine). More
These boards drive the stepper motors on the mightyboard (Makerbot Replicator 1, 2 and 2X motherboard). They are compatible with both Rev E and Rev G mightyboards (Ie All Makerbot Replicator Machines) More
Makerbot R2/2X- End stop cable (cable D) (rev 2) - UNTIL SOLD OUT
This cable is used to connect the X Y and Z endstop boards to the motherboard. It is used on the Markerbot Replicator Rev H (post sept 2013) 2 and 2 X machines, and includes 3 ferrits pre-fitted. IMPORTANT : This version is for Rev H motherboards. Not rev G - pre oct 2013. Also the X length is only 90cm long and requires an Endstop Jumper cable to be purchased separately.
Not used on the Replicator 1 Ply wood models, or rev G machines. If you have a rev G Replicator 2 or 2x - pre oct 2013 edition, those cables are now discontinued. You can fit this version with the jumpercable just ferrites are a bit tight for space under base plate. This is the cable only and does not include the endstop boards More
Replicator 2 and 2X LCD Interface Cable (Cable Assembly A)
This is the grey ribbon cable that connects the LCD screen of the Replicator 2 and 2X to the motherboard. It really never fails, so if you are thinking of replacing it check it is not the LCD carrier first More
This ribbon cable extrends the X Endstop cable. It connects to the X endstop and the XYZ endstop cable, providing extra length at the X motor end. All rev H Motor cables require this extrension. More
This die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 X 16cm. The backing peals off for easy adhesion. Price is per sheet (also available in bulk packs)
We manufacture this tape to have a strong adhesive and be better for PLA adhesion than painters tape, or Makerbot blue tape sheets More
100x Bulk Pack Blue Tape Precut Sheet (for Replicator 1,2,2X)
This is a 100 sheet pack of our die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 x 16cm. The backing peels off for easy adhesion. More
25x Bulk Pack Blue Tape Precut Sheet (for Replicator 1,2,2X)
This is a 25 sheet pack of our die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 x 16cm. The backing peels off for easy adhesion. More
This heater cartrige has short (10cm long) cables with a molex male pin connector. The cartrige is 23mm long and 6mm in diameter. It is made in Australia by Bilby3D and is a non-genuine exchange for the Makerbot Replicator 2 and 2X heater cartrige. More
This insert slots easily into the left hand belt mount on a Makerbot Replicator 2 or 2X to fix wearing damage. It slots easily into the outside of the mount and allows you to tighten belts and start printing again without having to remove the rods and entire belt mount. Note : includes the plastic 3d printed part only, does not include pulley or rod. Please oil the rod regularly to prevent this occuring again. More
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
Perth - Belmont, WA
3D Printers
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
Materials / Filament
3D Scanners
Parts and Spares
Tools & Jigs