These metal fittings are used for holding pneumatic (compressed air) tube. Designed for tube with a 4mm diameter made of Nylon or PU (PolyUrethane), they also work better than anything else we have found with PTFE tubing, which is very hard to hold due to its low friction. Has plastic collar - push down to release.
MicroSwiss All Metal Hotend Kit for FlashForge Finder, Guider, Inventor 2/2S/2SE-FFtc
Genuine Micro-Swiss all metal hotend upgrade for the FlashForge Guider, Guider 2
Finder, FinderPlus and Inventor2 recomend - ptKitMK10TC3
Comes with 0.4mm nozzle, range of other sizes available More
These metal fittings are used for holding pneumatic (compressed air) tube. Designed for tube with a 4mm diameter made of Nylon or PU (PolyUrethane), they also work better than anything else we have found with PTFE tubing, which is very hard to hold due to its low friction. Has plastic collar - push down to release.
0.4mm Nozzle for MK10 Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
Genuine Micro-Swiss all metal hotend upgrade for MK10 style extruders.
MK10 Extruders most notibly used on the FlashForge Dreamer, Inventor1 and Creator Pro 2016 and Dremel Idea Builder. It also fits the Wanhao i3 and Cocoon More
This turbine/turbo fan is often used to blow air onto the filament as it comes out of the nozzle, but it will work in any application where you need the air coming out of the fan circumferentially instead of axially
More
Tool for Clearing Extruder Jams (in barrel or feeder)
This tool kit is specifically designed to be inserted into your 3D Printer feeder to push down any broken material and assist in clearing blockages in the barrel and or feeder. More
Teflon Tube for FlashForge Creator Pro 2 Extruder Barrel-CP2
Genuine FlashForge replacement part to line the barrel/throat/heatbreak in your extruder.
The tube deteriorates after ~400 hours of printing, depending on your printing temperatures and materials More
Capricorn Tube for Creator Pro 2 Extruder Barrel-CP2
Regular PTFE barrel liners blacken and shrink after a couple of hundred hours printing, especially if printing at higher temepratures.
The Capricorn PTFE tube is modified to better withstand high temperatures, extending life More
These straight cut gears have the advantage over a hobbed gear in that the profile of the teeth is much deeper - so they dont get clogged as quickly - they get a better grip on the filament for longer. More
This is Micro Swiss All Metal Hotend kit with redesigned cooling block for Wanhao i3, Wanhao i3 Plus and all other i3 clones with the following improvements:
- Slotted Clamping system
- No set screw to ding and damage thermal tube
- Significantly better heat transfer (this is a big one!!!)
- Easier disassemble and adjustments
- Precise control on bore diameter
Heater Cartridge for Dreamer and Inventor 1 only-FFD > UNTIL SOLD OUT
Genuine Spare part for FlashForge Dreamer and Inventor 1 only heater cartridge.
Note : Flashforge CreatorPro cable is different (see image 3, ptHeatCart4024)
Flashforge Finder, Guider (1 and 2) and Inventor2 also have a short heater. This is not compatible
More
This silicon sock is 2mm longer, to accomodate the e3D Brass Heaterblock which is slightly longer than the standard part.- (Cartridge Style Thermistors only) More
This 1 inch wide ceramic tape is used to wrap your heater block and reduce heat transfer to both the extruder and your work piece. Fix by wrapping in kapton tape.
The tape on your Reprap will need replacing from time to time, especially when a print fails and the melted plastic gets caught up in the print head - it can sometimes stick to the ceramic tape and rip it on removal - careful not to pull on the temperature sensor wire! More
Machined Lever for Creator Pro - Right Side and Wanhao i3
This is a replacement lever and extruder plate for Dual Extruders (Right Side Only).
Lever and plate are CNC machined from 6061 billet aluminum, with weight reduction features.
Also suitable for the Wanhao i3
More
These metal fittings are used for holding pneumatic (compressed air) tube. Designed for tube with a 4mm diameter made of Nylon or PU (PolyUrethane), they also work better than anything else we have found with PTFE tubing, which is very hard to hold due to its low friction. Has plastic collar - push down to release.
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread, but has a larger and 0.6mm hole, which it sometimes used for faster printing and with metal and PETG filaments. Total Length 13mm
More
The short barrel / throat / heatbreak for the FlashForge High Temperature hotend, found on leter version of the FlashForge Guider2s (with a red nozzle duct) More
This is a replacement lever for Wanhao i3 and all of its clones. The Lever Arm is CNC machined from 6061 billet aluminum, with weight reduction features More
This is a brushless fan, similar to that used in the Makerbot Replicator 2 with a nozzle attachement to blow cool air on the printout and rapidly set the plastic for better overhangs and thus higher resolution More
Micro Swiss Bowden Dual Gear Extruder features the same quality construction as the Direct Drive extruders. It is designed to be a bolt-on replacement to most of the Bowden extruder machines on the market. More
This complete hotend kit from RepRap discount includes; nozzle, heater block, barrel/heat barrier, fined heat sink, heater cartridge, thermistor, fan, mount and more in a plastic case More
FlashForge Thermocoupler - Short for Dreamer-FFD > UNTIL SOLD OUT
Discontinued - Use ptThermoFFshCon and cut the connector off!
Genuine FlashForge thermocoupler
M4 brass fitting at sensing end (Note: our other thermocouplers and heater blocks are all M3)
Crimped terminals at motherboard end
~11cm lead length - Suited to the FlashForge Dreamer which has a terminal board on the extruder carriage More
0.2mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
0.3mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube. More
Thermal grease to increase the conduction of heat from chip to heatsink or heat resistor to heater block to thermistor.
Thermal Conductivity > 1.8W/m-k
White, non-toxic, tasteless, non-corrosive. More
This is an aftermarket brass barrel for Ultimaker 3D Printers . It has the unique feature of a hex partway down the barrel to allow tightening without straining on other parts
0.6mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread and 0.4mm tip hole. Total Length 13mm. The main hole is for filament with 2.85/3mm diameter or 3mm OD PTFE tube.
This stainless steel barrel has continuous thread so it is more universal than our standard barrel. It also has been drilled out larger at one end and a piece of teflon (PTFE) tube inserted to reduce the chances of "barrel lock" which can stop filament feeding resulting in a failed print and otherwise only solved with the oily rag trick (see our support articles)
More
This is a replacement lever for Wanhao Duplicator 6. Lever is CNC machined from 6061 billet aluminum, with weight reduction features. To match extruder color, this lever is anodized with matte black anodizing More
0.8mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
Machined Lever Assembly for Finder, Guider and Creator Pro - Left Side
This is a replacement lever and extruder plate for Dual Extruders (Left Side Only).
Lever and plate are CNC machined from 6061 billet aluminum, with weight reduction features.
More
1.0mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
1.2mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
Set of 10 bearings have an inner diameter of 8mm, Outer Diameter of 22mm and Width of 7mm - with metal dust covers. They are a standard size for many things, including spinners, roller blades, scooters and roller skates More
Please note: The signal line only supports the 3D touch sensor produced by trianglelab. We are not sure if the sensors of other merchants are compatible. We are also not sure if BL TOUCH is compatible. Please confirm that your sensor was manufactured by TriangleLab before purchasing. More
This teflon (PTFE) tube is used to make filament feeder tubes (or line the barrel on older 3mm J-Heads). They greatly reduce the chance of snagging between your filament spool and the extruder head without causing much drag.
Order by the metre. 1m should be enough for a single extruder machine.
Inner Diameter: 2mm
Outer Diameter: 3mm
All the nuts bolts, washers, springs and more you need to put together a Wades or Gregs extruder - see the more info for a full parts list. Does not contain plastic parts, barrel or the hot end. More
This Polyimide (also known as Kapton) Tape is a high temperature insulative tape. It uses a silicon based adhesive to withstand high temperatures up to 260 C. More
Ball Bearing - 608zz - used for many parts of a Reprap
These bearings have an inner diameter of 8mm, Outer Diameter of 22mm and Width of 7mm - with metal dust covers. They are a standard size for many things, including spinners, roller blades, scooters and roller skates More
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
More
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
More