Prices + Stock updated 10 May @ 13:42
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Over time (and with high temperatures), these need replacing.
Be sure to run preheat before removing the nozzle to fit
Also fits Raise 3D pro 3 extruders (upper)
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
Barrel for Flashforge Guider / Finder - FFptfe
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Buy Now
Extruder Heatsink for Guider 2 / 2S - FFptfe - FFtc
Genuine FlashForge replacement part
Buy Now
Extruder Heatsink for Inventor 2, 2S and 2 Special Edition-FFptfe-FFtc
Genuine FlashForge replacement part
Buy Now
Heater Cartridge for the Guider 2, Inventor 2/2s/se (24V, 18.5 long)-FFptfe-FFtc
Genuine FlashForge replacement part for the Guider 2 (NOT THE GUIDER 1-see specs tab), Inventor 2/2S/2SE
Buy Now
0.2mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
0.2mm Nozzle - M7 Thread for MK10 Extruder - Twin Clad Coated-FFptfe
This This wear resistant nozzle by AVN/Micro Swiss suits a range of printers with 1.75mm filament. It has an M7 thread and 0.2mm hole.
Buy Now
0.3mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
0.4mm Genuine FlashForge Nozzle - M7 Thread for MK10 Extruder-FFptfe
This is a genuine nozzle from FlashForge. M7 tread.
Buy Now
0.4mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads and PTFE lining)
Buy Now
0.4mm Nozzle - M7 Thread for MK10 Extruders - Wear Resistant Twin Clad Coating-FFptfe
This This wear resistant nozzle by Micro Swiss suits a range of printers has an M7 thread and 0.4mm hole.
Buy Now
0.5mm Nozzle - M7 Thread for MK10 Extruders - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
0.6mm Nozzle - M7 Thread for MK10 Extruder - TwinClad Coating-FFptfe
This wear resistant nozzle by Micro Swiss suits a range of printers with an M7 thread and 0.6mm hole
Buy Now
0.8mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage.
Buy Now
Heater Block for the FlashForge Finder, Guider, Inventor 2-FFptfe-FFtc
Genuine heater block for the FlashForge Finder series, Guider Series and Inventor 2
Copyright 2011-2024 Bilby3D Pty. Ltd.
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
Perth - Belmont, WA
3D Printers
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
Materials / Filament
3D Scanners
Parts and Spares
Tools & Jigs