Prices + Stock updated 10 May @ 13:42
Genuine Spare part for FlashForge Dreamer and Inventor 1 only heater cartridge.
Note : Flashforge CreatorPro cable is different (see image 3, ptHeatCart4024)
Flashforge Finder, Guider (1 and 2) and Inventor2 also have a short heater. This is not compatible
Heater cartridge is 26mm long, 6mm in diameter.
24V, 40W
Total length is 145mm long (including cartridge)
Connectors are raw cable
Dimensions: Cartridge 6mm diameter, 26mm long. Cables 120mm long
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
Aftermarket Heater Block for the FlashForge Dreamer/Pro/Inv 1-FFD
Aftermarket heater block for the FlashForge Dreamer, Creator Pro and Inventor 1
Buy Now
FlashForge Thermocoupler - Short for Dreamer-FFD > UNTIL SOLD OUT
Discontinued - Use ptThermoFFshCon and cut the connector off!
Genuine FlashForge thermocoupler
M4 brass fitting at sensing end (Note: our other thermocouplers and heater blocks are all M3)
Crimped terminals at motherboard end
~11cm lead length - Suited to the FlashForge Dreamer which has a terminal board on the extruder carriage
Buy Now
0.4mm Genuine FlashForge Nozzle - M7 Thread for MK10 Extruder-FFptfe
This is a genuine nozzle from FlashForge. M7 tread.
Buy Now
Pre-Cut Ceramic tape with Kapton - UNTIL SOLD OUT
Suits the Creator Pro, Dreamer and Inventor machines as well as a wealth of others. It is not self adhesive and you need Kapton tape to attach to your heat block.
Buy Now
Heater Cartridge - 40W 24V
This ceramic core heater cartridge has a variety of heating possibilities from hot ends/ extruders to heated beds.
Buy Now
Ceramic tape with Kapton for Finder, Inventor2, Guider2 - UNTIL SOLD OUT
Suits the Finder, Inventor2, Inventor2s, Inventor2SE, Guider, Guider2 and Guider2s machines as well as many others. It is not self adhesive and you need Kapton tape to attach to the heater block.
Buy Now
Barrel for Flashforge Guider / Finder - FFptfe
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
Heater Block for FlashForge Creator Pro 2 (IDEX)-CP2
Genuine FlashForge Heat block for the Creator Pro 2 (IDEX) - Left and Right identical
Buy Now
FlashForge Thermocoupler for Creator Pro 2-CP2
Genuine FlashForge Replacement Thermocoupler - heat sensor
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Buy Now
All Metal Hot End Assembly for FlashForge Guider 2 / 2S-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge
Buy Now
All Metal Hot End Assembly for FlashForge Inventor 2/2SE-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge. This edition has the shorter heat sink (see more information page)
Buy Now
FlashForge Hot End Assembly for Guider2s - 300°C - FFam
Genuine Flashforge HotEnd Assembly for the Guider2S
With a brass 0.4mm nozzle and is rated to 300 °C
Buy Now
Heater Block for the FlashForge Finder, Guider, Inventor 2-FFptfe-FFtc
Genuine heater block for the FlashForge Finder series, Guider Series and Inventor 2
Copyright 2011-2024 Bilby3D Pty. Ltd.