Prices + Stock updated 24 Apr @ 16:30
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Genuine Flashforge Part.
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
Stainless Steel barrel with PTFE (teflon) liner
This stainless steel barrel has continuous thread so it is more universal than our standard barrel. It also has been drilled out larger at one end and a piece of teflon (PTFE) tube inserted to reduce the chances of "barrel lock" which can stop filament feeding resulting in a failed print and otherwise only solved with the oily rag trick (see our support articles)
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Extruder Heatsink for Guider 2 / 2S - FFptfe - FFtc
Genuine FlashForge replacement part
Buy Now
Extruder Heatsink for Inventor 2, 2S and 2 Special Edition-FFptfe-FFtc
Genuine FlashForge replacement part
Buy Now
Heater Cartridge for the Guider 2, Inventor 2/2s/se (24V, 18.5 long)-FFptfe-FFtc
Genuine FlashForge replacement part for the Guider 2 (NOT THE GUIDER 1-see specs tab), Inventor 2/2S/2SE
Buy Now
0.2mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
0.2mm Nozzle - M7 Thread for MK10 Extruder - Twin Clad Coated-FFptfe
This This wear resistant nozzle by AVN/Micro Swiss suits a range of printers with 1.75mm filament. It has an M7 thread and 0.2mm hole.
Buy Now
0.3mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
0.4mm Genuine FlashForge Nozzle - M7 Thread for MK10 Extruder-FFptfe
This is a genuine nozzle from FlashForge. M7 tread.
Buy Now
0.4mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads and PTFE lining)
Buy Now
0.4mm Nozzle - M7 Thread for MK10 Extruders - Wear Resistant Twin Clad Coating-FFptfe
This This wear resistant nozzle by Micro Swiss suits a range of printers has an M7 thread and 0.4mm hole.
Buy Now
0.5mm Nozzle - M7 Thread for MK10 Extruders - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
0.6mm Nozzle - M7 Thread for MK10 Extruder - TwinClad Coating-FFptfe
This wear resistant nozzle by Micro Swiss suits a range of printers with an M7 thread and 0.6mm hole
Buy Now
0.8mm Nozzle - M7 Thread for MK10 Extruder - Stainless Steel-FFptfe
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage.
Buy Now
FlashForge Nozzle Set for Guider 2 High-Temp Hotends - FFam
Nozzle set with toughened drive gear and tools for the Guider2S with a high-temperature hotend. This will have a RED nozzle duct
Buy Now
0.6mm Brass Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
Extruder Heatsink for Guider 2S - High Temperature Version - FFam
Genuine FlashForge replacement part
For the High-Temp (300°C) hotend with the red cooling duct
Buy Now
Heater Block for FlashForge Guider 2S HT - FFam
Genuine FlashForge spare part
this heater block suits those G2S with the High-Temp (300°C) hotends
Does Not include Grub screw or Bolt
Buy Now
0.4mm Toughened Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
0.4mm Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
Teflon Tube for FlashForge Guider 2 - High Temp HotEnd - FFam
26mm length to suit ptHotEndAssFFg2HT - made from Capricorn PTFE Tube
Buy Now
FlashForge Hot End Assembly for Guider2s - 300°C - FFam
Genuine Flashforge HotEnd Assembly for the Guider2S
With a brass 0.4mm nozzle and is rated to 300 °C
Buy Now
Heater Block for the FlashForge Finder, Guider, Inventor 2-FFptfe-FFtc
Genuine heater block for the FlashForge Finder series, Guider Series and Inventor 2
Copyright 2011-2024 Bilby3D Pty. Ltd.
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
Perth - Belmont, WA
3D Printers
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
Materials / Filament
3D Scanners
Parts and Spares
Tools & Jigs