Prices + Stock updated 10 May @ 13:42
Genuine FlashForge replacement part for the Guider 2 (NOT THE GUIDER 1-see specs tab), Inventor 2/2S/2SE
Power: 24V 40W (important Finder and old guiders are 12 V)
Cartrige Size: 18.5mm long to cables, 6.2mm diameter
Cable: 116mm long, raw wire ends
Compatibile with: Guider 2/2s, Inventor 2/2s/2SE models
Note: Older Guiders use ptheatcartFFG as they are 12V not 24V
Dimensions: 125x7.9x24.4mm
Next >
Genuine FlashForge replacement partThis product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
Barrel for Flashforge Guider / Finder - FFptfe
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Extruder Heatsink for Guider 2 / 2S - FFptfe - FFtc
Genuine FlashForge replacement part
Buy Now
Extruder Heatsink for Inventor 2, 2S and 2 Special Edition-FFptfe-FFtc
Genuine FlashForge replacement part
Buy Now
Ceramic tape with Kapton for Finder, Inventor2, Guider2 - UNTIL SOLD OUT
Suits the Finder, Inventor2, Inventor2s, Inventor2SE, Guider, Guider2 and Guider2s machines as well as many others. It is not self adhesive and you need Kapton tape to attach to the heater block.
Buy Now
MicroSwiss All Metal Hotend Kit for FlashForge Finder, Guider, Inventor 2/2S/2SE-FFtc
Genuine Micro-Swiss all metal hotend upgrade for the FlashForge Guider, Guider 2
Finder, FinderPlus and Inventor2 recomend - ptKitMK10TC3
Comes with 0.4mm nozzle, range of other sizes available
Buy Now
All Metal Hot End Assembly for FlashForge Guider 2 / 2S-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge
Buy Now
All Metal Hot End Assembly for FlashForge Inventor 2/2SE-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge. This edition has the shorter heat sink (see more information page)
Buy Now
FlashForge Hot End Assembly for Guider2s - 300°C - FFam
Genuine Flashforge HotEnd Assembly for the Guider2S
With a brass 0.4mm nozzle and is rated to 300 °C
Copyright 2011-2024 Bilby3D Pty. Ltd.
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
Perth - Belmont, WA
3D Printers
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
Materials / Filament
3D Scanners
Parts and Spares
Tools & Jigs