Printrboard Motherboard for Printrbot Printers - UNTIL SOLD OUT
Drop in replacement for the motherboard found on most (pre RasberryPi / OctoPrint) machines. Supplied with the Unified Firmware (Legacy Models), other firmware and instructions, please see the Printrbot website.
Outputs for 4 motors (X,Y,Z, and Extruder), Extruider and Bed Heaters
Inputs for X,Y,Z and E stops
Micro-SD Card slot and Micro-USB slots
This is the latest edition board with a 6 pin power connector. Note Rev D and earlier boardshave a 4 pin power connector and need a jumper cable 4-6 or 8 pin. Available seperately (product code ptPwr4to8pin) More
This die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 X 16cm. The backing peals off for easy adhesion. Price is per sheet (also available in bulk packs)
We manufacture this tape to have a strong adhesive and be better for PLA adhesion than painters tape, or Makerbot blue tape sheets More
100x Bulk Pack Blue Tape Precut Sheet (for Replicator 1,2,2X)
This is a 100 sheet pack of our die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 x 16cm. The backing peels off for easy adhesion. More
25x Bulk Pack Blue Tape Precut Sheet (for Replicator 1,2,2X)
This is a 25 sheet pack of our die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 x 16cm. The backing peels off for easy adhesion. More
This is the threaded rod that fits vertically to the Printerbot Simple 2 (metal) to provide Z (UP-Down) movement. It screws into the coupler, that can also be upgraded to a ridge coupler. It is 19cm long with tapered ends, has a right hand thread and is 1/4 More
Acme threaded Z Rod for Printrbot Plus (11 inches long)
This is the threaded rod that fits vertically to the Printerbot Plus to provide Z (UP-Down) movement. It screws into the coupler, that can also be upgraded to a ridge coupler. It is 11 long with tapered ends, has a right hand thread and is 3/8-12 More
This it a 4 pin to 8 pin cable for CPU / ATX power supplies. It may be required for the Printrbot Heater bed upgrade on the Simple 2 and Plus machines to provide extra cable length, or bridge from 4 Pin power supply to 6 pin mother board connector. More
Printrbot Aluminum direct drive extruder is a work of art. Its elegant design makes it really stand out. Plus it is reversible to accommodate dual extruder setups. It is easy to adjust but rock solid. It holds both the 1.75 Ubis Ceramic and Ubis Catridge hot ends perfectly. Enjoy the benefits of machined aluminum.
* Machined drive gear included. Motor not included More
Damaged the bed on your Printrbot Simple 2 ? Its easy to fit a new one.
This is a perfectly level Mic 6 aluminum print bed with for your Printrbot Simple Metal. This is the Simple Metal Heated Bed Upgrade ... minus the heat. (w mounting wings and hardware for installation)
Compatibility: Printrbot Simple Metal (Model 1403) More
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
Perth - Belmont, WA
3D Printers
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
Materials / Filament
3D Scanners
Parts and Spares
Tools & Jigs