Prices + Stock updated 19 Nov @ 15:27
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
TwinClad XT is a nickel composite coating for very low frction. Over a 360 brass base, it gives a lower coefficient of friction than PTFE (Teflon) over nickel
This is dimensioned the same as our standard nozzle, as used on the Makerbot MK8 extruders.
ALWAYS run preheat before changing nozzles to avoid stripped threads.
Is is compatible with Makerbot:
- Replicator 1 (Single and Dual)
- Replicator 2
- Replicator 2x
- Craftbot 2
- CraftBot PLUS
- BQ Witbox
- BQ Prusa i3 Hephestos
- Creality CR-10
(Note Changing nozzle on a Smart Extruder is difficult and may void Smart Extruder warranty)
- Replicator 5th Gen (Note Changing nozzle on smart extruder will void warranty)
- Replicator Mini
- Replicator Z18
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
0.4mm Nozzle - M6 Thread for MK8 Extruders - Twin Clad Coated
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
Buy Now
0.6mm Nozzle - M6 Thread for MK8 Extruders - Wear Resistant TwinClad Coating
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread, but has a larger and 0.6mm hole, which it sometimes used for faster printing and with metal and PETG filaments. Total Length 13mm
Buy Now
0.4mm Nozzle - M6 Thread for MK8 Extruders - Brass
This is the most common nozzle across all 3D Printers. Most notably Makerbot Replicator 1, 2 and 2x, Prusa, older FlashForge
Buy Now
Nozzle Clearing Tool
This hand held tool is a safer way to clear blockages in your nozzle
Buy Now
Stainless Steel Barrel with TwinCladXT Coating
This tube is an improvement over the stock MakerBot Replicator 1 and MakerBot Replicator 2 thermal barrier tube. Also used on many other types of 3D Printers
Buy Now
0.6mm Nozzle - M7 Thread for MK10 Extruder - TwinClad Coating-FFptfe
This wear resistant nozzle by Micro Swiss suits a range of printers with an M7 thread and 0.6mm hole
Buy Now
Barrel for Flashforge Guider / Finder - FFptfe
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Buy Now
0.4mm Nozzle - M7 Thread for MK10 Extruders - Wear Resistant Twin Clad Coating-FFptfe
This This wear resistant nozzle by Micro Swiss suits a range of printers has an M7 thread and 0.4mm hole.
Buy Now
Micro Swiss Extruder + HotEnd for Creality CR-10 / Ender 3 Printers
Micro Swiss Direct Drive Extruder is a drop in system for CR10 / Ender Printers. We include the MicroSwiss HotEnd.
- No modification required, simple plug and play
- No printed brackets or sandwiches
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
Micro Swiss Extruder + HotEnd for Creality Ender 5 Printers
Micro Swiss Direct Drive Extruder is a drop in system for Ender 5 Printers. We include the MicroSwiss HotEnd.
- No modification required, simple plug and play
- No printed brackets or sandwiches
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Copyright 2011-2023 Bilby3D Pty. Ltd.
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
Perth - Belmont, WA
3D Printers
Brisbane - Spring Hill, QLD
Bilby 3D Technical Support
3D Printer Service and Repair
Courses and Training
Materials / Filament
3D Scanners
Parts and Spares
Tools & Jigs